Log in is not required to search. In the red banner above select: I Want To > Search > Permits

Plan Review Notes

Plan Review Notes For Permit 20090252
Permit Number	20090252
Review Stop	FIRE
Sequence Number	1

Notes

Date	Text
2020-09-14 09:10:39.00000	KERRY BARNETT FIRE SAFETY CONSULTING, LLC
	43951 CR 54E, KATHLEEN, FL 33849

	FIRE SAFETY INSPECTOR & PLANS EXAMINER CELL (813)
	778-4981
	KERRY BARNETT E-MAIL:
	KBARNETT@FIRESAFETYCONS.COM
	________________________________________

	PLAN REVIEW #: 20-071 REVIEW FOR: PARKERAIRE
	PROJECT: PAPA JOHNS (HOOD/DUCT) CONTACT: DAVID PAKER
	LOCATION: LAKE PLACID, FL TELEPHONE: 239-997-2665
	ADDRESS OF JOB: 121 US HWY 27
	PAGES: 12

	SEPTEMBER 11, 2020


	I HAVE RECEIVED AND REVIEWED THE PLANS (CAPTIVE AIRE)
	FOR A COMMERCIAL GREASE HOOD/DUCT FOR A PAPA JOHNS AT
	ADDRESS ABOVE. PLANS WERE REVIEWED TO THE BEST OF THIS
	REVIEWER’S ABILITY TO ENSURE COMPLIANCE WITH THE
	FLORIDA FIRE PREVENTION CODE, NFPA 96, AND ANY OTHER
	APPLICABLE CODES, STANDARDS, RULES, AND STATUTES.
	COMMENTS ARE LISTED BELOW. AT THIS TIME, THE PLANS ARE
	NOT APPROVED. ADDITIONAL INFORMATION SHALL BE SUBMITTED
	BASED ON THE COMMENTS BELOW. SHOULD ANYONE HAVE ANY
	QUESTIONS, THIS AUTHORITY MAY BE CONTACTED VIA
	TELEPHONE OR EMAIL NOTED ABOVE.

	1. A SCALED DRAWING/PLAN SHALL BE SUBMITTED SHOWING THE
	INSTALLATION OF THE HOOD AND DUCT FOR THIS PROJECT. AN
	ELEVATION DRAWING SHALL BE INCLUDED NOTING HOW THE DUCT
	ROUTES FROM THE HOOD TO THE FAN. ACCESS DOORS SHALL BE
	INDICATED AS WELL. THIS IS NEEDED TO DETERMINE DISTANCE
	FROM COMBUSTIBLES TO DETERMINE OF ANY ADDITIONAL FIRE
	PROTECTION IS REQUIRED EITHER BY FIRE WRAP OF USE OF
	DOUBLE WALL DUCT. IT IS IMPORTANT TO NOTE THE
	CONSTRUCTION TYPE MATERIAL (LIMITED COMBUSTIBLE,
	NON-COMBUSTIBLE, COMBUSTIBLE) THAT THE DUCT AND HOOD
	WILL INSTALLED WITHIN.
	2. A SCALED DRAWING/PLAN SHALL ALSO SHOW ROOF LAYOUT TO
	ENSURE SETBACKS ARE MET FROM EXHAUST TO ANY AIR INLET.
	3. ENSURE APPLIANCES ARE INSTALLED UNDER THE HOOD ARE
	IN ACCORDANCE TO THE HOOD PLACARDS.
	4. ENSURE ROOF TOP FAN SHALL BE HINGED AND HAVE A
	GREASE CUP. ENSURE THERE IS ENOUGH SLACK IN THE
	ELECTRICAL CONNECTION TO ALLOW THE FAN TO BE TIPPED
	WHEN HOOD/DUCT IS BEING CLEANED.
	5. ENSURE HOOD FANS ARE PROPERLY WIRED SO EXHAUST FANS
	REMAIN ON WHEN SYSTEM IS ACTIVATED AND MAKE UP AIR
	SHUTS DOWN.
	6. IF A FIRE WRAP IS TO BE USED, SUCH AS FIRE MASTER
	FAST WRAP” PROVIDE SPEC SHEETS ON WRAP.
	7. ENSURE ACCESS PANEL HAS REQUIRED LISTED GASKET.
	PROVIDE SPEC SHEET OF ACCESS PANEL.
	8. ENSURE THE FAN MEETS THE REQUIRED 10 FT HORIZONTAL
	DISTANCE FROM ANY OTHER AIR INLET
	9. THE FAN CURB SHALL BE A MINIMUM OF 18 INCHES ABOVE
	ROOF TOP WITH TOP OF FAN BEING A MINIMUM OF 40 INCHES
	ABOVE THE ROOF TOP.

	INSPECTIONS REQUIRED:

	1. LIGHT TEST
	2. TEST & BALANCE (COPY OF REPORT TO BE GIVEN TO THIS
	AUTHORITY AT FINAL INSPECT)
	3. FINAL – CAN BE COMPLETED AT TIME OF SUPPRESSION
	FINAL. APPLIANCES SHALL BE IN PLACE.

2020-09-10 10:48:09.00000	EMAILED TO KERRY BARNETT KBARNETT@FIRESAFETYCONS.COM